Dsc 1864 Programming Manual

Advertising
  1. Dsc 1616 Programming Guide
  2. Dsc 1864 Programming Manual Online
  3. Dsc 1864 Programming Manual
  4. Dsc 1832 Programming Cheat Sheet
  5. Dsc Pc1864 Programming
  6. Dsc 1832 Programming Worksheet
  7. Dsc 1864 Installation Manual Download

How to Program:

DSC recommends filling in the Programming Worksheet with the required
programming information before programming the system. This will reduce the
time required to program and will help eliminate errors.

To enter Installer Programming press [*][8][5555].
The Program light will FLASH (or in the case of the programmable LCD keypad
the display will change to ‘Enter Section’).

An error tone indicates the installer code entered is not correct.
Press [#] to clear any key presses and try again

.

PC1616/PC1832/PC1864 STANDARD INSTALLATION GUIDE This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual. Dsc PC1616; PC1832; PC1864 Pdf User Manuals. View online or download Dsc PC1616; PC1832; PC1864 User Manual, Installation Manual. Programming 10. The keypads represented in this manual can be used with the following Control Units: PC580, PC1555MX, PC1616, PC1832, PC1864, PC5010, PC5015 or the PC5020. IMPORTANT INFORMATION This equipment complies with Part 68 of th e FCC Rules and, if th e product was approved July 23, 2001 or later, the requirements adopted by the ACTA. The DSC 1864 shares the same programming as the 1616, and the 1832 as they are basically the same panel, with a different number of zones, etc. Default Installer code: 5555.

The Armed and Ready lights indicate programming status:

Armed Light ON

Panel waiting for 3-digit section number

Ready Light ON

Panel waiting for data to be entered

Ready Light FLASHING

Panel waiting for HEX data to be entered

NOTE:

You cannot enter installer programming while the system is armed or
in alarm.

Programming Toggle Options:

Enter the 3-digit programming section number.

The Armed light will turn OFF and

The Ready light will turn ON.

The keypad will display which toggle options are ON or OFF according to
the chart below:

To toggle an option ON or OFF, press the corresponding number on the
keypad. The display will change accordingly.

When all the toggle options are configured correctly, press the [#] key to
exit the program section.

Nikon connex software.

The Ready light will turn OFF and the Armed light will turn ON.

Dsc 1616 Programming Guide

NOTE:

Dsc

If the panel is a local system, press [#] to skip this step.

NOTE:

In addition to the standard digits 0-9, HEX digits can also be
programmed if required.

Programming Decimal and Hexadecimal (HEX) Data:

Enter the 3-digit programming section number.

The Armed light will turn OFF and The Ready light will turn ON.

Enter the data written in the boxes.

For sections that require multiple 2 or 3 digit numbers, the keypad will
double-beep after each 2 or 3 digit entry and move to the next item in
the list. After the last digit in the section is entered, the keypad will
beep rapidly 5 times and exit the program section. The Ready light will
turn OFF and the Armed light will turn ON.

For sections that do not require data for every box (such as phone
numbers) press the [#] key to exit the program section after entering all

the required data. The Ready light will turn OFF and the Armed light
will turn ON.
At any time the [#] can be pressed to exit any program section. All
changes made up to that point will be saved.

HEX (or hexadecimal) digits are sometimes required. To enter a HEX
digit, press the [*] key to begin HEX programming. The Ready light will
FLASH. Refer to the chart below and press the number corresponding
to the HEX digit required. The Ready light will continue to FLASH.
Press [*] again to return to normal decimal programming. The Ready
light will turn ON.

HEX [A]

[*] [1] [*]

HEX [B]

[*] [2] [*]

HEX [C]

[*] [3] [*]

HEX [D]

[*] [4] [*]

HEX [E]

[*] [5] [*]

Dsc 1864 Programming Manual Online

HEX [F]

[*] [6] [*]

How to Exit Installer Programming:

To exit installer programming, press the [#] key when the panel is
waiting for a 3-digit section number (the Armed light is ON).

Viewing Programming

LED and LCD5501Z Keypads

Any programming section can be viewed from an LED or LCD5501Z key-
pad. When a programming section is entered, the keypad will immediately
display the first digit of information programmed in that section.
The keypad displays the information using a binary format, according to
the following chart:

See Hex data

entry instructions

Press any of the Emergency keys (Fire, Auxiliary or Panic) to advance to
the next digit.
When all the digits in a section have been viewed, the panel will exit the
section: the Ready light will turn OFF, and the Armed light will turn ON,
waiting for the next 3-digit programming section number to be entered.
Press the [#] key to exit the section

LCD Keypad

When a programming section is entered, the keypad will immediately dis-
play all the information programmed in that section. Use the arrow keys (<
>) to scroll through the data being displayed. To exit the section, scroll
past the end of the data displayed, or press the [#] key.

DLS Programming

Hardware Setup - Local (PC-Link)

Connect a RS-232 to PC-Link Cable between the Computer with DLS
Software installed and the alarm panel to be programmed.

[401] First Downloading Option Code

The 1

st

Dsc

toggle option in this section is used to enabled/disable Downloading.

Configure the options as required and press [#] to exit

Jarvis understands that and has you covered with two modes, Office Mode & Quiet hoursContextually AwareJarvis is contextually aware of time & device settings and he adapts himself based on when you wake him up.Easter eggsApart from the regular chores, Jarvis tries his best to keep you entertained. Shuffle the list, play or stop.Bluetooth Support betaIf your device is running JellyBean or up, you can use your bluetooth headset to control Jarvis, play media over it and do tons of other stuffs. Jarvis app for android. This feature is still in beta so don’t be alarmed if some bugs pop up.General searchesAsk Jarvis general questions like “Who is the first president of USA”, “How many meters are in a kilometer”, “Convert 100 cm to inches”Office hours & Night modeIt’s always irritating when your phone notifies you something when you are in office or when you are home getting a good sleep. NotificationsGet voice notifications about weather, news, battery status & power levels.Automatic wallpaper updateJarvis can update your home screen wallpaper automatically almost every day keeping it refreshed.Theme supportCustomize the appearance of the app by selecting from Mark I, Mark II & Mark III themes.Device controlControl your phone settings like Flash, WiFi etcPeople reminderA one of a kind reminder which allows you to link reminders to your contacts so you get reminded when you get or make a phone call.Media playbackPlay media by name, album, artist.

.

PROGRAMMING

Keypad Type

Dsc 1864 Programming Manual

Option ON

Option OFF

LED

Zone Light ON

Zone Light OFF

Fixed-Message LCD

Indicator # ON

Indicator # OFF

Programmable-Message LCD

# Displayed

Dash [-] Displayed

HEX [A]
HEX [B]
HEX [C]
HEX [D]
HEX [E]

Not Supported
Simulated [*] key
Simulated [#] key
Dial tone search
Two second pause

Press [*][2][*]
Press [*][3][*]
Press [*][4][*]
Press [*][5][*]

Opt

Default

Description

2

I__I

Dsc 1832 Programming Cheat Sheet

ON

User can enable DLS Window

OFF

User can NOT enable DLS Window

Advertising
This manual is related to the following products:

Dsc Pc1864 Programming

Popular Brands

Dsc 1832 Programming Worksheet

Popular manuals

Dsc 1864 Installation Manual Download

    • 1
      Installation Guide
    • 2
      Table of Contents
  • 3
    1 Installation & Wiring

    • 4
      Keybus Wiring
    • 4
      Zone Wiring
    • 4
      Zone Expanders
    • 4
      Bell Wiring
    • 6
      AUX Power Wiring
    • 6
      PGM Wiring
    • 6
      Telephone Line Wiring
    • 6
      Ground
    • 6
      Battery
    • 6
      AC Wiring
  • 7
    2 User Commands

    • 7
      Away Arming
    • 7
      Stay Arming
    • 7
      Disarming
    • 7
      Commands
    • 8
      Programming User Codes
    • 9
      Function Keys
  • 10
    3 Programming

    • 10
      How to Program
    • 10
      Programming Toggle Options
    • 10
      Programming Decimal & Hexadecimal Data
    • 11
      How to Exit Programming
    • 11
      Viewing Programming
    • 11
      DLS Programming
  • 12
    4 Programming Descriptions

  • 28
    5 Programming Worksheets

    • 31
      About Your Security System
    • 31
      Keypad Display Symbols
    • 31
      Fire Detection
    • 31
      General System Operation
    • 31
      Pk5500 Language Selection
    • 32
      Emergency Keys
    • 32
      Function Keys
    • 32
      Away Arming
    • 32
      Stay Arming
    • 33
      Testing Your System
    • 33
      Guidelines for Locating Smoke Detectors
    • 34
      Fcc Compliance Statement
    • 34
      Household Fire Safety Audit
    • 34
      Fire Escape Planning
    • 34
      New Zealand Telecom Network
    • 40
      System Timers
    • 42
      Reporting Codes
    • 63
      Limited Warranty
    • 64
      Additional Information
    • 64
      Important Information